性能
噪音水平 |
45 dB |
发声警报器 |
Y |
浪涌保护功能 |
Fax, Modem, Network, Telephone |
能量控制
输入工作电压(最大值) |
300 V |
输入工作电压(最小值) |
156 V |
效率 |
98.6% |
最大电流 |
8 A |
电源输入频率 |
50/60 Hz |
能量波动功率 |
613 J |
输出功率(瓦特-安培) |
900 VA |
输出功率 |
540 W |
电池
热插拔电池 |
Y |
半载典型备用时间 |
16 min |
全载典型备用时间 |
4.6 min |
替换电池盒 |
APCRBC123, APCRBC123J |
冷启动 |
Y |
支持的的电池数量 |
1 |
环境条件
非运行高度 |
0 - 15000 m |
工作高度 |
0 - 3000 m |
端口 & 界面
交流电(AC)插座数量 |
5 AC outlet(s) |
其他功能
额定输入电压 |
230 V |
名义输出电压 |
230 V |
Back-UPS Pro 900VA, 540W, 230V, 5x Schuko CEE 7, RJ-11, RJ-45, USB, 10.72kg
BR900G-RS Features
- Green mode
Patent-pending operating mode that bypasses unused electrical components in good power conditions to achieve very high operating efficiency without sacrificing any protection.
- Boost and Trim Automatic Voltage Regulation (AVR)
Eliminates voltage fluctuations as a source of AV signal degradation and component power-supply stress.
- Battery failure notification
Provides early-warning fault analysis on batteries enabling timely preventive maintenance
- Power-saving outlets
Automatically cuts power to idle equipment to conserve electricity.
- Resettable circuit breaker
Easy recovery from overloads; no need to replace a fuse.
- LCD display
Alpha-Numeric Display which displays system parameters and alarms.
- Data-line Protection
Protection of data lines (Ethernet, Coaxial and Phone lines) ensures complete protection of your equipment from surges. It is very important to protect your equipment from “back door” electric surges traveling through data lines, as they can be as damaging to your equipment as surges traveling over power lines.
- Replace Battery LED
An external Replace Battery LED informs the end-user that the battery needs to be replaced.
- Cold-start capable
Provides temporary battery power when the utility power is out.
- Serial connectivity
Use any Home Automation network to monitor and control the S20 through its RS-232 serial port. For information on how to communicate with the S20, see APC's Application Note #102. Crestron and AMX installers should visit their respective websites for information on how to integrate the S20 into those networks.
- Hot-swappable batteries
Ensures clean, uninterrupted power to protected equipment while batteries are being replaced
- Disconnected battery notification
Warns when a battery is not available to provide backup power.
- Dataline surge protection
Provides protection of connected equipment from power surges on the data lines.
- Automatic self-test
Periodic battery self-test ensures early detection of a battery that needs to be replaced.
- Adjustable voltage-transfer points
Maximizes useful battery life by widening the input voltage window or tightening the output voltage regulation.
- Adjustable voltage sensitivity
Provides the ability to adapt the UPS for optimal performance in specific power environments or generator applications.
- Audible alarms
Provides notification of changing utility power and UPS power conditions
- USB connectivity
Provides management of the UPS via a USB port (not available on all models).
- Serial connectivity
Provides management of the UPS via a serial port.
- Boost and Trim Automatic Voltage Regulation (AVR)
Gives higher application availability by correcting low and high voltage conditions without using the battery (not available on all models).
- Intelligent battery management
Maximizes battery performance, life, and reliability through intelligent, precision charging.
- Battery replacement without tools
Enables fast battery replacement, lowering Mean Time to Repair (MTTR).
- LCD graphics display
Text and mimic diagrams that display modes of operation, system parameters and alarms.
- Automatic Voltage Regulation (AVR)
Automatically steps up low voltage and steps down high voltage to levels that are suitable for your equipment.