数据传输
MAC 地址表 |
8000 entries |
交换容量 |
32 Gbit/s |
巨型帧 (Jumbo frames) |
9126 |
端口 & 界面
继电器输出 |
1 |
基本交换 RJ-45 以太网端口数量 |
16 |
接线端子台端口 |
Y |
基本交换 RJ-45 以太网端口类型 |
Gigabit Ethernet (10/100/1000) |
以太网铜缆技术 |
100BASE-TX, 1000BASE-T, 1000BASE-TX, 100BASE-T, 10BASE-T |
联网
广播风暴控制 |
Y |
自动 MDI / MDI - X 检测功能 |
Y |
全双工传输 |
Y |
网络标准 |
IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z |
流量控制支持 |
Y |
动态主机配置协议客户 |
Y |
10G支持 |
N |
设计
外壳材料 |
Metal |
DIN导轨安装 |
Y |
液晶显示器指示灯 |
Y |
国际保护(IP)代码 |
IP30 |
认证 |
UL Class 1 Division 2 Groups A/B/C/D; ATEX Zone 2, IECEx, UL508, FCC Part 15 Subpart B Class A, EN 55011/55022, Class A, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, IEC 60068-2-27, IEC 60068-2-32, IEC 60068-2-6 |
墙壁支架 |
Y |
能量控制
输入电压 |
12 - 48 V |
功耗(一般操作) |
8 W |
重量和尺寸
宽度 |
74 mm |
高度 |
120 mm |
深度 |
84 mm |
管理功能
网上管理 |
Y |
支持服务质量(QoS) |
Y |
开关类型 |
Unmanaged |
性能
程序包缓冲区内存 |
4.1 MB |
平均故障间隔时间 |
2788343 h |
环境条件
运行湿度范围(H-H) |
10 - 95% |
储存温度范围 (T-T) |
-40 - 85 °C |
储存相对湿度范围(H - H) |
10 - 95% |
以太网电源(PoE)
电源保护功能 |
Over current, Reverse polarity |
系统要求
兼容性操作系统 |
32-bit/64-bit Windows XP/Vista/7, Windows Server 2003/2008/2008 R2 |
另外
产品色彩 |
Blue |
数据传输率(最大) |
100 Mbit/s |
巨型帧 |
Y |
运行温度范围(T - T) |
-40 - 75 °C |
Gigabit Ethernet, 100m, 100Mbps, 16xRJ-45, 8k MAC, 32Gbps, 9126 Jumbo Frames, 12-48V, 8W, 74x84x120mm, IP30, Metal, 2788343h MTBF
Introduction
SE300 series is the industry’s first design for Ethernet Green, IEEE802.3az - Energy Ethernet switches that cut power usage by up to 60%, significantly saving energy usage in the field and reducing total cost of ownership over 24/7. Advantech B+B SmartWorx SE300 series monitored switches can be used as plugand-play unmanaged switches right out of the box. Installing the iView Network Management Software gives them basic monitoring and management capabilities as well. They bridge the gap between unmanaged switches and significantly more expensive, fully managed solutions. When enabled with iView2, these switches provide IP address assignment, allowing for a static IP address or an address that is discoverable via DHCP in the network. Then, these switches have the ability to use Modbus/TCP to communicate with HMI/SCADA software and SNMP to communicate with NMS (Networking Management Software) at the same time. This gives full access control to both control engineers and IT managers.
Basic Monitoring & Management Capabilities
iView2 gives network managers the ability to monitor and manage eWorx SE300 series switches from a central location. It features an intuitive Graphical User Interface (GUI) that provides a real-life representation of all installed eWorx SE300 Series switches, displaying device functions, port settings, device status information and traffic statistics via SNMP. iView2 can also configure eWorx SE300 series switches monitoring capabilities for automation applications via the popular Modbus TCP/IP protocol. Control engineers can use existing HMI/SCADA software to integrate the network status by creating extra tags for real-time monitoring. iView2 is a standalone software that supports multiple platforms and operating systems.