联网
| 可支持的电缆类型 |
Cat5, Cat5e |
| 自动检测 |
Y |
| 私人 VLAN |
Y |
| 端口镜像 |
Y |
| 广播风暴控制 |
Y |
| VLAN支持 |
Y |
| IGMP侦听 |
Y |
| 自动 MDI / MDI - X 检测功能 |
Y |
| 示踪 VLAN |
Y |
| 速率限制 |
Y |
| 链路汇集 |
Y |
| 生成树协议 |
Y |
| 基于端口的 VLAN |
Y |
| 流量控制支持 |
Y |
| 动态主机配置协议客户 |
Y |
| 动态主机配置协议服务器 |
Y |
| 10G支持 |
N |
| 全双工传输 |
Y |
性能
| Auto-negotiation 自动协商功能 |
Y |
| 处理器频率 |
416 MHz |
| 缓冲区大小 |
512 KB |
| 内置存储器 |
128 MB |
| 固件可升级 |
Y |
| 内置处理器 |
Y |
| 闪存 |
16 MB |
协议
| 支持网络协议 |
IPv4/v6 |
| 管理协议 |
SNMP V1, V2, V3 |
管理功能
| 网上管理 |
Y |
| 支持多重播放 |
Y |
| 交换层 |
L2 |
| 支持服务质量（QoS） |
Y |
以太网电源（PoE）
| 电源保护功能 |
Over voltage, Overload, Short circuit |
| 以太网（PoE）供电总功率概算 |
200 W |
| 支持以太网（PoE） |
Y |
端口 & 界面
| 基本交换 RJ-45 以太网端口类型 |
Gigabit Ethernet (10/100/1000) |
| 已安装的 SFP 模块数量 |
2 |
| 基本交换 RJ-45 以太网端口数量 |
16 |
| 以太网铜缆技术 |
100BASE-TX, 1000BASE-T, 10BASE-T |
| 千兆以太网(铜)端口数量 |
16 |
数据传输
| MAC 地址表 |
8000 entries |
| 存储转发 |
Y |
| 交换容量 |
36 Gbit/s |
| 巨型帧 (Jumbo frames) |
9000 |
| VLAN 数量 |
4096 |
| 吞吐量 |
26.8 Mpps |
| 组播组过滤数目 |
8000 |
安全
| 鉴别 |
Guest VLAN, MAC-based authentication, Port-based authentication |
| 环路保护 |
Y |
| BPDU 过滤/保护 |
Y |
16-Port Gigabit Ethernet PoE+ Web-Managed Switch w / 2 SFP Ports
Save installation time and money with PoE
The Intellinet 16-Port Gigabit Ethernet PoE+ Web-Managed Switch with 2 SFP Ports (560931) is designed to pass both data and electrical power to a number of PoE-compatible devices via standard Cat5e or Cat6 network cables. Equipped with sixteen Gigabit Ethernet ports, all of which support 802.3at/af Power over Ethernet (PoE/PoE+), this switch can power Wireless LAN access points and bridges, VoIP (Voice over Internet Protocol) telephones, IP surveillance cameras and more while delivering network speeds of up to 1,000 Mbps.
Power over Ethernet 802.3at
The Intellinet 16-Port Gigabit Ethernet PoE+ Web-Managed Switch with 2 SFP Ports supports the IEEE 802.3at protocol and is designed to inject up to 30 watts of power per port*. IEEE802.3af or IEEE802.3at compliant devices attached to the switch require no additional power, thus eliminating the time and expense of electrical rewiring and minimizing the unsightly clutter caused by power supplies and adapters in awkward places such as ceilings and walls. Any mix of PoE and non-PoE devices is supported, and thanks to its short circuit, overload and high-voltage protection function, your equipment is well-protected. For devices that are not 802.3at/af compliant (legacy wireless access points or network cameras), we suggest use of an Intellinet PoE/PoE+ Splitter.
Eliminate Bottlenecks with Gigabit Speeds
Equipped with 16 auto-sensing 10/100/1000 Mbps RJ45 Gigabit Ethernet ports, the 16-Port PoE Web-Managed Desktop Gigabit Switch (560931) offers plenty of performance for your computers, servers and other networking devices. In addition, two small form-factor pluggable GBIC module slots (SFP) provide fiber connectivity for greater distances.
Full Layer 2+ Management Features
The switch includes full Layer 2+ Management features. The software set includes up to 4k 802.1Q VLAN and advanced protocol VLAN, private VLAN and MVR. There are eight physical Quality of Service queues, IPv4/v6 Multicast filtering, Rapid Spanning Tree Protocol to avoid network loop, Multiple Spanning Tree Protocol to integrate VLAN and spanning tree, LACP, LLDP; sFlow, port mirroring, cable diagnostic and advanced network security features. It also provides Console CLI for out-of-band management and SNMP, Web GUI for in-band management.
Advanced Security
The Intellinet 16-Port PoE+ Web-Managed Desktop Gigabit Switch (560931) supports advanced security features. For secure switch management, HTTPS and SSH are provided. In addition, the login password and configuration packets are secured. Port binding allows to bind a specific MAC address to a port, and then only that MAC has the privilege to access the network. Thanks to 802.1X port based access control, every user needs to be authorized first when they want to access the network. AAA stands for Authentication, Authorization and Accounting with RADIUS, TACAS+ server. The Layer 2+ access control list (ACL) allows the user to define the access privilege based on IP, MAC address or Port number.
