联网
| 布线技术 |
10BASE-T, 100BASE-TX, 1000BASE-T, 1000BASE-X |
| 双机热备系统 |
Full, Half |
其他功能
| 接收功率 |
-23 - 3 dBmW |
| 发射功率 |
-5 - 0 dBmW |
性能
| 可支持的光纤电缆直径 |
9/125 µm |
| 光纤模式结构 |
Single-mode |
| 最大传输距离 |
80000 m |
| 波长 |
1550 nm |
另外
| 数据传输率（最大） |
1000 Mbit/s |
| 连接方式 |
Wired |
| 以太网路(RJ-45)连接接口数量 |
1 |
10/100/1000BASE-T / 1000BASE-X, DF, SM, SC, RJ-45, 80 km, 1550 nm, 18 dBm, USB Power Adapter Cable
10/100/1000BASE-T to 1000BASE-X Ethernet Media Converter
- The miConverter GX/T is a 10/100/1000 copper to 1000 fiber media converter
- Conforms to 10BASE-T, 100BASE-TX, 1000BASE-T, and 1000BASE-X specifications
- Supports jumbo frames up to 10,240 bytes
- Supports dual fiber and single-fiber 1000BASE-X SFP transceivers for standard or CWDM wavelengths
- Fiber port supports multimode and single-mode fiber with ST and SC connectors and single-fiber with SC connectors
- Plug-and-Play capability
- Both the fiber and UTP ports support auto-negotiation
- UTP port supports 10/100/1000Mbps and Half/Full-Duplex
- User-selectable Link Modes for quick fault detection
- Auto or manually configured Pause function for flow control
- USB power via optional Power Adapter Cable
- Domestic, Universal and Country/Region specific power supply options
- Models support terminal connector for DC power
- Small and lightweight (less than 5 ounces)
- LIfetime Warranty and free 24/7 Technical Support
The miConverter GX/T is a miniature 10/100/1000BASE-T UTP copper to 1000BASE-X fiber media converter that supports jumbo frames up to 10,240 bytes. The miConverter GX/T provides cost-effective fiber connectivity from Ethernet switches to diagnostic equipment, desktop and laptop computers.
The GX/T features Small Form Pluggable (SFP) transceivers that support 1000BASE-X for interoperability with Gigabit fiber equipment. SFP transceivers enable adaptability to different fiber types, speed and distances, and support Coarse Wave Division Multiplexing (CWDM) technology to increase the bandwidth capacity of fiber infrastructure.
The GX/T also supports SC and ST fixed fiber connectors for multimode, single-mode fiber; and single mode single-fiber models are available.
The Plug-and-Play capability of the miConverter GX/T simplifies fiber-to-the-laptop and fiber-to-the-desktop deployments. Both the fiber port and the UTP port support auto-negotiation, an IEEE standard which defines how all the communicating devices automatically perform their configuration functions. Auto-negotiation achieves the best possible mode of operation (speed, duplex mode and Pause mode) between the devices.
The auto-negotiation feature can be disabled on both ports (for manual configuration) using DIP-switches on the module. This is useful in a situation where the GX/T is connected to a non-negotiating device and the configuration parameters must be set manually.
Network flow control is managed by the Pause function (configured via auto-negotiation or manually) that prevents network congestion on both the UTP and fiber ports. When Pause is enabled and the device is experiencing network congestion, it will send out a Pause signal to its link partner, instructing it to slow down data transmission.
The GX/T generates a remote fault indication when it detects link fault conditions, and reports detection of these signals by displaying status on the LED. Through user DIP-switch configuration, the detection of these indicators or link modes can also be propagated to the other port on the GX/T as a means of notifying connected end-devices of the link fault.
Diagnostic data is provided through LED indicators that assist in network installation and maintenance. The LEDs report the availability of power, port activity and link status and speed.
The miConverter GX/T combines Gigabit Ethernet connectivity with the lightweight design and low-power consumption required for both permanent deployment and mobile service networks.
The external AC power supply is available in US, Universal and Country/Region specific models. Country/Region specific models feature optional interchangeable connectors, allowing for compatibility with electrical outlet types found around the world. The GX/T is also available with a terminal connector for DC power between 5 to 12 volts.
The miConverter GX/T can be mounted in the miConverter 18-Module Power Chassis to consolidate individual modules into a rack-mount form factor that can be deployed where multiple fiber optic links are distributed from UTP switch equipment. The chassis powers converter modules with barrelstyle DC connectors, and is available with a single universal AC, 24VDC or 48VDC internal power supply. This compact, high-density chassis is 1.5 rack units high, and can be mounted in a standard 19” or 23” equipment rack.
Weighing less than 5 oz. with the USB Power Adapter Cable, the miConverter GX/T can easily fit into any pocket or laptop carrying case. It can also be attached to portable equipment using the included Velcro strips or wall-mounted using the optional wall-mounting bracket kit.
