设计
外壳材料 |
Metal |
內置式 |
N |
液晶显示器指示灯 |
Y |
联网
双机热备系统 |
Full |
自动 MDI / MDI - X 检测功能 |
Y |
以太网的数据传输率 |
10, 100 Mbit/s |
以太网接口类型 |
Fast Ethernet |
以太网光缆技术 |
100BASE-FX |
支持的链路损耗结转(LLCF) |
Y |
支持的链路损耗回报(LLR) |
Y |
网络标准 |
IEEE 802.3, IEEE 802.3u |
以太网铜缆技术 |
10BASE-T, 100BASE-TX |
Auto-negotiation 自动协商功能 |
Y |
转换器输入接口 |
100Base-TX |
转换器输出接口 |
100Base-FX |
性能
发射功率(最小) |
-20 dBmW |
灵敏度 |
-32 dBmW |
可支持的光纤电缆直径 |
9/125 µm |
波分复用(WDM) |
N |
光纤模式结构 |
Single-mode |
最大传输距离 |
15000 m |
波长 |
1310 nm |
能量控制
输入电压 |
100-240 V |
输出电压 |
5 V |
外接电源转接器 |
Y |
接受频率 |
50/60 Hz |
输出电流 |
2 A |
环境条件
运行湿度范围(H-H) |
5 - 90% |
储存温度范围 (T-T) |
-40 - 70 °C |
储存相对湿度范围(H - H) |
5 - 90% |
重量和尺寸
深度 |
69 mm |
重量 |
200 g |
宽度 |
97 mm |
高度 |
26 mm |
认证标准
认证 |
FCC Class A, CE Class A |
另外
产品色彩 |
Black |
数据传输率(最大) |
100 Mbit/s |
连接方式 |
Wired |
以太网路(RJ-45)连接接口数量 |
1 |
运行温度范围(T - T) |
0 - 50 °C |
10/100BASE-TX to 100BASE-FX (SC, SM) Bridge Media Converter, 15km
PLANET FT-80x is a Fast Ethernet Bridge 100BASE-FX fiber to 10/100BASE-TX shielded twisted pair (STP) converter. It supports both half-duplex and full-duplex operations and a variety of fiber options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation in fiber-optic interface. The fiber port of the converter operates at 1310 nm and uses ST, SC, MTRJ, VF45 or WDM connectors. Multi-mode models that support distances up to 2km and single-mode models that support distances up to 15/20/35/50/60km are available.media and provide efficient solution to monitoring the net.
The FT-80x series is with LFP (Link Fault Pass-through function) (LLCF/LLR) and the DIP switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net. The DIP switch provides the disabling or enabling of the LFP function
LLCF (Link Loss Carry Forward) means when a device is connected to the converter and the TP line loses the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device is connected to the converter and the fiber line loses the link, the converter's fiber will disconnect the transmit link. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitoring the net.