Transition Networks C4TEF1017-110 Internal 155Mbit/s 1550nm Single-mode network media converter

1550 nm, single mode, SC to 4x RJ-48 + 10/100BASE-TX, RJ-45 + 6-pin DIN These products offer a low cost transport capability for four T1/E1, one Ethernet, and one RS232 data channel line. The converters provide copper connections compatible with G.703, AMI/B8ZS/HDB3, 10/100BASE-TX, as well as RS232 channel; while the optical connection will run at 155Mbps. TDM traffic is not mapped to Ethernet. A hardware-based solution guarantees the constant bit rate of TDM transport without requiring traffic management. The product provides physical layer status monitoring and alarm classification functions for Telecom operators to manage their fiber optic network and reduce operation and maintenance costs. Target applications of the converter include: FTTx, such as Fiber-to-the-Business, Fiber-to-the-Building, Fiber-to-the-MDU and Fiber-to-the-Home.

- Remote Management - Select stand-alone converters can be managed through SNMP when used in conjunction with a chassis based converter.
- Local and Remote Loopback - This feature puts a converter in a special mode that enables the device to loop back the signal from the RX port to the TX port on either media for testing and troubleshooting purposes.
- Auto-Negotiation for 10/100BASE-TX - Allows devices to perform automatic configuration to achieve the best possible mode of operations over a link.
- AutoCross™ - Automatically detects and configures the twisted pair port on the converter to the correct MDI or MDI-X configuration.
- Link Pass Through for Ethernet - Link Pass Through is a troubleshooting feature that allows the media converter to monitor both the fiber and copper RX ports for loss of signal.
- Pause (IEEE 802.3xy) - Pause signaling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed.
- Remote Fiber Loss Signaling
- AIS/TAOS
- LEDs for each data port
- DIP switches for line code, line length, local loopback or remote loopback
- T1/E1 mode switch
- Dry Relay Contacts on each TDM port
- Local (AUX) Management Interface (RS232 connector)
- Switch selection for Data or Management mode on RS232 interface
- Password protection
- Access to complete status information on local and remote device
- Switch or SNMP selected Baud rate operation
-
<b>SNMP Management Features</b>

-
<b>Report local converter status:</b>
- Fiber Link Status
- Copper Link Status for each T1/E1
- Hardware switch settings: LBO, AIS on C/F, HW/SW, speed
- AIS detected Fiber & Copper
- Model Number
- Copper & Fiber Connectors

-
<b>Local command operations include:</b>
- Loopback Fiber & T1/E1 per channel
- AIS TX on fiber on loss of copper link & AIS TX on copper on loss of fiber link
- Serial connection speed and parity (Software Mode)
- T1/E1 Mirror Port Modes (Port Trapping)
- Boot-load firmware upgrades
- Ethernet settings:
--- Auto-Negotiation Enable/Disable
---- Force speeds and modes on 10/100TX

-
<b>Remote converter status:</b>
- Fiber Link status
- Copper Link Status for each T1/E1
- Hardware switch settings: LBO, AIS on C/F, HW/SW, speed
- AIS detected Fiber & Copper
- Model Number
- Copper & Fiber Connectors

-
<b>Remote Commands:</b>
- Loopback Fiber & T1/E1 per channel
- Serial connection speed and parity (Software Mode)
- AIS TX on fiber on loss of copper link & AIS TX on copper on loss of fiber link
- T1/E1 Monitor Modes
- Ethernet settings (Software Mode):
--- Auto-Negotiation Enable/Disable
--- Force speeds and modes on 10/100TX
--- Transparent Link Pass Through Enable/Disable
--- Flow Control Enable/Disable
--- AutoCross™ Enable/Disable