Panduit S4X4BL6NM Fiber-Duct Channel
Used to carry the cables throughout the Fiber-Duct™ Routing System. Accepts cover C4BL6. Cover sold separately
Panduit DCF5EI Drop ceiling/entrance end fitting for use with LD5 raceway, Electric Ivory, ABS, Length 3.42 in, Width 1.6 in
Panduit FFWC2X2BL 2 x 2 Fiber-Duct Fitting. Attaches to channel to create a horizontal four way cross intersection. Cover included. Black
Panduit FCF4X4BL Fiber-Duct 4x4 System Fitting
4in x 4in coupler fitting used to join two sections of duct together. Fiber-Duct Coupler is not required at each fittin
Panduit RAEFXIW-X Power Rated Fittings, ABS, White
Power rated right angle/entrance end fitting for use with LD3, LDPH3, LDS3, LD5, LDPH5, LDS5, LD10 and LDPH10 racewa
Panduit RAF3EI-E Right angle fitting for use with LD3 raceway, Electric Ivory, ABS, Length 1.82 in
Panduit H2X2BL6 2x2 FiberRunner Hinged Slotted Channel
Panduct® type H hinged cover wide slot wiring duct, 2" W x 2" H, 6' length, PVC, black
Panduit OCFC10WH-X ABS, White
Outside corner fitting for use with LDPH10 raceway only. White
Panduit E4X4BL6 Fiber-Duct Slotted Channel
Used to carry the cables vertically to the front or the back of equipment racks throughout the system. Accepts cover C4BL6
Panduit CMPHF2 Cable Management D-Rings
D-rings installed on panel. 3.5"H x 19.0"W x 3.4"D (88mm x 483mm x 87mm)
Panduit FR12X4YL2 12x4 FiberRunner Channel
Used to carry the cables horizontally throughout the system. Accepts cable retainers FRCR12BL or hinged cover FRHC12YL2. Use
Panduit FCE2U FCE2U, Black
Holds up to eight QuickNet™ Cassettes, FAP adapter panels, or FOSM splice modules. Dimensions: 3.48"H x 17.60"W x 16.30"D (88.4mm x 447.
Panduit FCE1U FCE1U, Black
Holds up to four QuickNet™ Cassettes, FAP adapter panels, or FOSM splice modules. Dimensions: 1.73"H x 17.60"W x 16.30"D (43.9mm x 447.0
Panduit FRME1U Enclosure, Black
Holds up to three FAP or FMP adapter panels or FOSM splice modules. Bi-directional sliding drawers provides front and rear access to
Panduit FCE1 Enclosure, black
Holds up to four QuickNet™ cassettes, FAP or FMP adapter panels. Dimensions: 1.74"H x 19"W x 18"D (44.4mm x 483mm x 457.8mm
Panduit FRFWC12X4BL 12x4 Four Way Cross Fitting
Attaches to 12x4 channel and/or fittings to create a horiztonal four way cross intersection with two 12x4 exits. Accepts
Panduit FREC6X4YL 6x4 End Cap Fitting
Used for closing off open ends of the channel or fittings. No coupler required. Push-on installation
Panduit FRBC12X4BL 12x4 QuikLock Coupler
Pre-assembled coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bo
Panduit FRBC4X4YL 4x4 QuikLock Coupler
Pre-assembled coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bol
Panduit FREC12X4YL 12x4 End Cap Fitting
Used for closing off open ends of the channel or fittings. No coupler required. Push-on installation
Panduit FRT12X4BL 12x4 Horizontal Tee Fitting
Panduit FREC12X4BL 12x4 End Cap Fitting
Used for closing off open ends of the channel or fittings. No coupler required. Push-on installation
Panduit NK2FIWY NK 2-port, single gang, flush mount faceplate with labels, white
Panduit FRT12X4W6YL 12x4 Horizontal Tee with 6x4 Exit
Attaches to 12x4 channel and/or fittings to create a 90° horizontal branch with a 6x4 exit from straight horizontal
Panduit FRBC6X4YL 6x4 QuikLock Coupler
Pre-assembled coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bol
Panduit FRRA12X4YL 12x4 Horizontal Right Angle Fitting
Attaches to 12x4 channel and/or fitting to create a 90° horizontal turn from a straight horizontal run. Inside di
Panduit FRTSC12BL Split Cover for 12x4 Horizontal Tee Fitting
Optional split cover for the horizontal tee fitting FRT12X4BL. Snap-on feature allows cover to be install
Panduit FRBC12X4YL 12x4 QuikLock Coupler
Pre-assembled coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bo
Panduit CMBEI-X ABS, Electric Ivory
Mini-Com® 1-port blank module, reserves space for future use
Panduit LDPH5WH6-A Tamper resistant two-piece latching surface raceway. Supplied with pre-punched mounting holes and factory applied adhesive tape. Available in 6', 8',
Panduit T702BIW10 Twin-70 raceway base, 10 ft
Twin-70 raceway base, 10 foot length. Supplied with pre-punched mounting holes. 2' of cover needed for every 1' of Twin-7
Panduit FRFWC12X4YL 12x4 Four Way Cross Fitting
Attaches to 12x4 channel and/or fittings to create a horizontal four way cross intersection with two 12x4 exits. Accepts
Panduit FRHD2KTYL 2x2 Hinged Duct Vertical Cable Manager Kit
Provides secure, accessible route for cables spilling out from a vertical tee or spill-over junction to ra
Panduit FRTR12X4YL 3-Sided BRC Trumpet Spillout for 12x4 Exit
Used to limit the bend radius of the cable to 2" (50.8mm) when exiting from the 12x4 channel or a 12x4 hor
Panduit FIVRA2X2BL 2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 90° upward angle from a straight horizontal run. Used with outside vertical 90° angle fitti
Panduit FIVRA2X2YL 2 x 2 Fiber-Duct Fitting, Yellow
2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 90° upward angle from a straight horizontal run. Used with
Panduit FOVRA2X2YL Outside Vertical Right Angle Fitting
Attaches to channel to create a 90° downward angle from a straight horizontal run. Used with inside vertical 90°
Panduit FVT4X4YL 4x4 Vertical Tee
Attaches to channel to create a 90° vertical drop from a horizontal run. Accepts FIDT4X4BL, FTR4X4YL, S4X4YL6 or E4X4YL6 directly
Panduit FOVRA2X2BL 2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 45° downward angle from a straight horizontal run. Used with inside vertical 90° angle fitt
Panduit FIDT4X4BL 2-Port Spillout to 1.5" (38 mm) Inside Diameter Corrugated Tubing
Used to route cable into one or two pieces of 1.5" (38mm) diameter split corrugated
Panduit CFX5IW-X Coupler fitting for use with LD5, LDPH5, and LDS5 raceway.
specifications\nLDS non metallic surface raceway will be a one piece, solid\nraceway used
Panduit TFC5EI-X Tee fitting for use with LD5, LDPH5, and LDS5 raceway.
specifications\nLD non-metallic series low voltage, one-piece hinged design,\nsingle channel s
Panduit RAF5EI-E Right angle fitting for use with LD5 raceway.
Pan-Way® LD Surface Raceway System\nLD non-metallic series low voltage, one-piece hinged design, single
Panduit FRVT6X4YL 6x4 QuikLock Vertical Tee, 2 pcs
Attaches to 6x4 channel and/or fittings to create 90° vertical drop from a straight horizontal run. Hinged door incl
Panduit C3BL6 Type C Cover for Flush Cover Wiring Duct
Duct cover, 3" W x 6' length, PVC, black
Panduit ABMM-A-C Cable Tie Mounts - Adhesive Backed
4-Way adhesive backed cable tie mount, high temp, .75"x.75" (19.1mm x 19.1mm), white, standard package
Panduit LD3WH6-A Low Voltage Raceway
One-piece latching surface raceway. Supplied with pre-applied adhesive backed tape. Available in 6', 8', and 10' lengths
Panduit JB1FSWH-A Fast-Snap Single Gang Two-Piece Snap Together Outlet Box
Fast-Snap™ Single Gang Two-Piece Snap Together Outlet Box with adhesive backing. Box accepts
Panduit CFX10WH-X Power Rated Fittings
Coupler fitting for use with LD10, LDPH10, and LD2P10 raceway
Panduit ICFX10WH-X Power Rated Fittings
Inside corner fitting for use with LDPH10 and LD2P10 raceway
