B&B Electronics 485TBLED RS-232 RS-422/485 Blue serial converter/repeater/isolator

B&B Electronics 485TBLED RS-232 RS-422/485 Blue serial converter/repeater/isolator

MPN: 485TBLED
🚚 Select the country of delivery:
Delivery from:
Germany
Updating price ... 📣 Send Price inquiry Не поставляется
Delivery cost & estimated delivery time:
От
days

Where to buy and prices (Advertising *)

On Top
в наличии
* Alle Preise inkl. der jeweils geltenden gesetzlichen Mehrwertsteuer, ggfs. zzgl. Versandkosten. Alle Angaben ohne Gewähr. Preisänderungen sind in der Zwischenzeit möglich.

Technical specifications

On Top

Technical details

Serial ports quantity 2
Host interface RS-232
Output interface RS-422/485
Baud rate 115.2 Kbit/s

Power

Input voltage 9 - 14 V

Indication

LED indicators Data
DB25 Female, RS - 232, 115.2 kbps The 485TBLED converts unbalanced, full duplex RS -232 signals to balanced, full or half-duplex RS-422 or RS-485 signals. RS -485 is an enhanced version of the RS-422 Standard. It allows multiple drivers and receivers on a two -wire or four-wire system.
The RS-232 port, configured as a DCE port, has a female DB25 connector with pins 2 (TD input), 3 (RD output), and 7 (Signal Ground) supported. Pins 4 (RTS) and 5 (CTS) are tied together, and pins 6 (DSR), 8 (CD), and 20 (DTR) are also tied together. Pins 1 (Frame Ground) and 7 (Signal Ground) are connected straight through to the RS-485 terminal blocks. The RS-485 terminal blocks support Transmit Data (A-) and (B+), Receive Data (A-) and (B+), Frame Ground, Signal Ground, and +12 VDC input. See Schematic.
LEDs
The 485TBLED has two LEDs: a Transmit Data LED to show when the RS-485 driver is enabled and a Receive Data LED showing data appearing at pin 3 of the RS-232 port. These are very useful for d
etermining if data is getting through the converter. Note that the TD LED indicates that the RS -485 driver is enabled. Data must be present on pin 2 of the RS-232 side for data to be transmitted out of the RS-485 side. If no data is present, no data will be transmitted even though the TD LED is illuminated.
Flow Control
The 485TBLED uses two different methods to enable the RS-485 driver, either by toggling Request to Send (pin 4) of the RS-232 side, or by automatic sensing of the data on Transmit Data (pin 2) of the RS
-232 side. This option is user selectable by setting push-on jumpers located next to the terminal locks. See Fig. 1.Removing both sets of jumpers completely can also constantly enable the RS-485 driver and receiver. This makes the 485TBLED a ct like an RS-422 converter.
Baud Rate
There is a timing component on the converter, a resistor R9, see Fig. 1. This component is part of the automatic sensing circuit, and affects the baud rate at which the converter can be used in a two
-wire setup. This component, is factory selected to allow the converter to run at 9600 baud or higher. With this component, the RS-485 driver will shut off approximately 1ms after the last character has been sent. If you need to change the 485TBLED to a baud rate other than 9600 baud, you can hange this component. To change the baud rate, remove R9 and add through hole component R14
The Echo jumper is used in the two-wire mode, and allows you to prevent data being sent from the RS
-232 port from being echoed back to the RS -232 port. Up to 32 receivers can be driven by any one RS
-485 driver, allowing you to put together large systems with many drop points. If you are using termination resistors, they should be located at opposite ends of the system.
Proper operation of any RS-485 system requires the presence of a return path. The RS-485 Standard recommends that a third wire be used for this. For safety, a 100 ohm resistor should be connected between Signal Ground and the "reference wire" at every drop point. While it may be possible to interconnect Signal Grounds directly, this is not recommended due to the danger of circulating currents possibly being present.
No wire type or maximum run length is listed in the RS-485 Standard. However, the RS-422 Standard (which is very similar) recommends number 24AWG twisted pair telephone cable with a shunt capacitance of 16 picofarads per foot, and no more than 4000 feet of distance.
Фотографии

    Password recovery
    To recover your password, please enter in the box below your email address with which you have registered:
    The password reset code has been sent to your Email.
    Код уже был отправлен Вам ранее.
    Вы можете ввести его в поле выше, или получить новый код через сек.
    An error has occurred. Please check your e-mail address and try again.
    Ваш новый пароль:

    Name is empty


    Выберите страну доставки

    You have not written a message

    By clicking on the "Send" button, you agree that your data will be used to process your request. Further information and revocation instructions can be found in the data protection declaration.

    Your message has been sent!

    Close

    1
    Catalog
    Cancel Close
    Бренды:
      Выберите бренды
        Show more close
          Area search
          Worldwide
          Категории
            Product