Features
| Brand colour |
Grey |
| EMICODE |
EC 1 PLUS |
| Suitable for underfloor heating |
Y |
| Volume |
5 kg |
| Operating time |
1 h |
| Substance |
Powder |
| Material consumption (min) |
1.75 kg/m² |
| Material consumption (max) |
4 kg/m² |
| Suitable for |
Floor & wall |
| Shelf life |
12 month(s) |
| Water-resistant |
Y |
| Frost-resistant |
Y |
| Fast drying |
N |
Operational conditions
| Minimum operating temperature |
5 °C |
| Maximum operating temperature |
25 °C |
705 special adhesive, 5 kg
- Very low VOC-emission
- Emicode EC1 plus
- For in- and outdoor use
- Suitable for almost all subfloors
- Watertight (when applied as an impervious layer)
- Flexible
- Moisture- and frost-resistant
- Very suitable for tiles with an absorption capacity of 1% or less
- High initial adhesion strength
- High final bond strength
- Does not deteriorate with age
- Easy to apply
- For wall and floor
- Dust reduced
- Low chromate
<b>Substrate:</b>
- The subfloor must have a good tensile and compression strength. The subfloor should also be smooth, dry and free from grease, dirt and dust, according to the requirements of DIN 18 352.
- Wooden floors, made of floorboards, should be sufficiently supported underneath (maximum 70 cm distance between the beam). Screw water-resistant plywood (minimal 12 mm thickness) on top of this layer and prime completely with 685 Eurocoat.
- Apply 099 Dispersion Primer on gypsum-based walls to obtain an impervious layer between the tile adhesive and subfloor.
- Prime self-levelling anhydrite floors with 099 Dispersion Primer (drying time minimum 1 - 2 hours).
- In advance always seek our technical data sheets. In doubt about the application ask for technical advice.
<b>User manual:</b>
- Add 25 kg of 705 Watertight Tile Adhesive to approx. 6 litres of cool and clean tap water and stir the mortar for 1 minute, by using an electric stirrer (approx. 600 rpm), to a smooth and homogeneous mixture.
- After strirring wait for a few minutes, stir once again and apply the adhesive on the subfloor with the recommended adhesive spreader (see spreading capacity/notched spreader).
- Press the tiles within 15 to 20 minutes with a shuffling movement into the adhesive. Check regularly to ensure that the back of the tile is in full contact with the adhesive. Remove excess adhesive immediately from the joints.
- For the watertightness on floors in wet areas first apply an impervious layer of approx. 5 mm thickness with a flat trowel. Thereafter make adhesive strips with the recommended adhesive spreader. When it is absolutely necessary to obtain a water-resistant layer, make two actions. First apply an impervious layer of approx. 3 mm thickness with a flat trowel and let dry for minimum 5 hours. Thereafter apply a second layer and make adhesive strips.
- In dry areas make the adhesive strips with the recommended adhesive spreader in the usual way.
- Apply the mixed adhesive within 60 minutes. Do not add extra water!
- Under normal circumstances, i.e. a temperature of 20° C and a relative humidity of 65%, the joints may be filled after minimum 24 hours.
<b>Spreading capacity/notched spreader for powder tile adhesives:</b>
The smoothness of the subfloor and type of tile are determining for the adhesive spreader to be used. Selection of the notched spreader should be made in such way that a minimum adhesive contact of 80% is guaranteed (equally divided over the back of the tile). For outdoor purposes this contact must be 100%. Also counts for heavy-duty indoor floors, e.g. store and warehouse floors. Check the adhesive contact regularly.
- Spreader no. 19, 4x4 mm : Spreading capacity approx. 1.75 kg/m²
- Spreader no. 12, 6x6 mm : Spreading capacity approx. 2.5 kg/m²
- Spreader no. 13, 8x8 mm : Spreading capacity approx. 3.5 kg/m²
- Spreader no. 14, 10x10 mm : Spreading capacity approx. 4 kg/m²
