Gefen CAT5-1600A AV transmitter & receiver

Gefen CAT5-1600A AV transmitter & receiver

🚚 Select the country of delivery:
Delivery from:
Germany
Updating price ... 📣 Send Price inquiry Не поставляется
Delivery cost & estimated delivery time:
От
days

Where to buy and prices (Advertising *)

On Top
в наличии
* Alle Preise inkl. der jeweils geltenden gesetzlichen Mehrwertsteuer, ggfs. zzgl. Versandkosten. Alle Angaben ohne Gewähr. Preisänderungen sind in der Zwischenzeit möglich.

Technical specifications

On Top

Ports & interfaces

VGA (D-Sub) output ports 3
RJ-45 input ports 2
RJ-45 output ports 2
VGA (D-Sub) input ports 1
DC-in jack Y

Technical details

Maximum transfer distance 100 m
Type AV transmitter & receiver
Cable types supported Cat5
Audio system stereo

Power

External power adapter Y
Operating voltage 5 V
Extender, CAT5, 1920x1200, 100m, Horizontal Frequency Range: 15 - 70kHz, Vertical Frequency Range: 30 - 170Hz, Video Amplifier Bandwidth: 350MHz, 1x VGA In (Sender), 1x VGA Out (Sender), 2x VGA Out (Receiver), 3.5mm Audio In, 3.5mm Audio Out, 1x USB B (Sender), 4x USB A (Receiver) <b>Extends VGA, audio, and USB 2.0 up to 330 feet (100 meters) over two CAT-5 cables</b>

The Gefen CAT5-1600A extends VGA, Audio, and USB up to 330 feet (100 meters) using CAT-5 cables. Display resolutions up to 1920x1200 are supported. A local monitor can be connected to the Sender unit and up to two monitors can be connected to the Receiver unit. Four USB connectors on the Receiver unit allow control of the computer system from a KVM workstation. Mini-stereo connectors extend analog audio. A Power-saving "Green Mode" can be set via DIP switches on the Sender and Receiver. When activated, both units will go into low-power Standby Mode when the Sender's VGA input signal disappears.

<b>How It Works</b>

Place the CAT5-1600A Sender unit next to the VGA source. Use the included VGA cable to connect the source to the Sender unit. Optionally connect a local monitor to the Sender unit using a VGA cable. Connect up to two monitors to the Receiver unit with VGA cables. Connect the USB devices to the input and output connectors. For audio, connect a mini-stereo cable between the audio source and the audio input on the Sender unit. Connect a mini-stereo cable between the audio output on the Receiver unit and the audio device. Use two CAT-5 cables to connect the Sender unit to the Receiver unit.

Connect the included locking power supplies to both the Sender unit and Receiver unit then connect both power cables to available electrical outlets. The computer can now be controlled from the KVM workstation.
Фотографии

    Password recovery
    To recover your password, please enter in the box below your email address with which you have registered:
    The password reset code has been sent to your Email.
    Код уже был отправлен Вам ранее.
    Вы можете ввести его в поле выше, или получить новый код через сек.
    An error has occurred. Please check your e-mail address and try again.
    Ваш новый пароль:

    Name is empty


    Выберите страну доставки

    You have not written a message

    By clicking on the "Send" button, you agree that your data will be used to process your request. Further information and revocation instructions can be found in the data protection declaration.

    Your message has been sent!

    Close

    1
    Catalog
    Cancel Close
    Бренды:
      Выберите бренды
        Show more close
          Area search
          Worldwide
          Категории
            Product